Hardware Specifications


Vendor/Brand	Nokia
Model	G-010G-T
ODM	CIG
ODM Product Code	G-97CP
Chipset	RTL9601D
Flash	16MB
RAM	32MB
System	Linux (Luna SDK 1.9.0)
2.5GBaseT	Yes
Optics	SC/APC
IP address	192.168.100.1 (after a factory reset the ONT uses 10.89.42.157/16)
Web Gui	✅ user `admin`, password `1234`
SSH	Can be enabled, locked down by iptables rule
Telnet	✅ user `ONTUSER`, password `1234`, but has access to GponSLID and not GponCLI
Serial	✅
Serial baud	115200
Serial encoding	8-N-1
Form Factor	ONT

Nokia G-010G-T Winbond 25Q128 Flash memory

Nokia G-010G-T Semtech GN25L95 Laser Driver

List of software versions

3FE49717AOCK12
3FE49717AOCK49

List of partitions

dev	size	erasesize	name	format
mtd0	00040000	00001000	“Boot”	Binary
mtd1	00002000	00001000	“Config”	jffs2
mtd2	00002000	00001000	“ImageA”	cramfs
mtd3	0003c000	00001000	“ImageB”	cramfs

Kernel command line arguments

console=ttyS0,115200  
root=/dev/mtdblock3 
mtdparts=sflash:512K@0x0(Boot),0x180000@0x80000(Config),7M@0x200000(ImageA),7M@0x900000(ImageB) 
rootfstype=cramfs 
hasEeprom=0 
5srst=0 
eqvid=3FE49715ADAA01 
uboot_version=V3.9.08 
major=f4 
minor=1

Note: When Reset button is held for over 5 seconds then parameter 5srst=0 is changed to 1.

Serial

The ONT has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be accessed from the top surface. To accept TX line commands, the GND of the TTL adapter should be attached to the ONT’s shield:

Note Some USB TTL adapters label TX and RX pins the other way around: try to swap them if the connection doesn’t work.

Usage

Note

Once you’re logged in, a custom menu will be shown and you’ll be able to access the linux shell by first typing system followed by shell:

ONT>enable
#ONT>login
User name:ONTUSER
Password: ****

The enable password can be generated using the following form:

Accessing Full Shell

To access a complete linux shell just type:

#ONT>system
#ONT/system>shell

To exit the shell and reach the parent menu type exit or x, in each menu the help command will show how to use the shell

GPON ONU status

Getting the operational status of the ONU

#ONT>traffic
#ONT/system>pon
#ONT/system/pon>show link

 ----------------- LINK STATE -----------------
 Link State:              ACTIVE
 Operation State Machine: OPERATION (O5)
 ----------------- STATE  END -----------------

Querying a particular OMCI ME

#ONT>system
#ONT/system>mib
#ONT/system/mib>show 256
Table Ontg, Ont-g, total 1 instances

EntityID                  = 0x0000
VID                       = "ALCL"
Version                   = AA BB CC DD EE FF 11 22 33 44 55 66 00 00
SerialNum                 = AA BB CC DD EE FF 11 22
TraffMgtOpt               = 0
AtmCCOpt                  = 0
BatteryBack               = 1
AdminState                = 0
OpState                   = 0
OnuSurvivalTime           = 0
Loid                      = ""
Password                  = ""
AuthState                 = 0
OntState                  = 1

GPON/OMCI settings

Committing changes to the OMCI MIB tables for GPON operation

#ONT>system
#ONT/system>mib
#ONT/system/mib>reset

Getting/Setting ONU GPON Serial Number

#ONT>system
#ONT/system>misc
#ONT/system/misc>eqsn set "ALCL00000001"
---ATECMDRESULT--- OK
#ONT/system/misc>eqsn get
eqsn: ALCL00000001
---ATECMDRESULT--- OK

Getting/Setting PLOAM

#ONT>system
#ONT/system>misc
#ONT/system/misc>pon_passwd set "123456789"
---ATECMDRESULT--- OK
#ONT/system/misc>pon_passwd get
pon_passwd: 31323334353637383900
---ATECMDRESULT--- OK
#ONT/system/misc>register_id set "123456789"
---ATECMDRESULT--- OK
#ONT/system/misc>register_id get
pon_passwd: 31323334353637383900
---ATECMDRESULT--- OK

Setting OMCI software version (ME 7)

The following command must be typed into the standard linux shell:

# echo SWVER=3FE49337AOCK80 > /mnt/rwdir/sys.cfg

Getting/Setting OMCI hardware version (ME 256)

#ONT>system
#ONT/system>misc
#ONT/system/misc>eqvid get
eqvid: 3FE45458ABAA06
hex_eqvid: 0x3346453435343538414241413036
---ATECMDRESULT--- OK
#ONT/system/misc>eqvid set "YOUR_CUSTOM_VID"

Getting/Setting OMCI vendor ID (ME 256)

#ONT>system
#ONT/system>misc
#ONT/system/misc>vendor get
vendor: ALCL
---ATECMDRESULT--- OK
#ONT/system/misc>vendor set "ALCL"
---ATECMDRESULT--- OK

Getting/Setting OMCI equipment ID (ME 257)

#ONT>system
#ONT/system>misc
#ONT/system/misc>eqid set "YOUR_CUSTOM_EQUID"
---ATECMDRESULT--- OK
#ONT/system/misc>eqid get
eqid: YOUR_CUSTOM_EQUID
hex_eqid: 0x594F55525F435553544F4D5F4551554944000000000000
---ATECMDRESULT--- OK

Getting/Setting MAC address

mac1 = Lower MAC ID (printed on label)

mac2 = Upper MAC ID (usually = mac1+3)

#ONT>system
#ONT/system>misc
#ONT/system/misc>mac1 get
mac1: aa.bb.12.34.56.78
---ATECMDRESULT--- OK
#ONT/system/misc>mac2 get
mac2: aa.bb.12.34.56.7b
---ATECMDRESULT--- OK
#ONT/system/misc>mac1 set 12:34:56:11:22:33
---ATECMDRESULT--- OK
#ONT/system/misc>mac2 set 12:34:56:11:22:44
---ATECMDRESULT--- OK

Advanced settings

Setting management IP

#ONT>system
#ONT/system>misc
#ONT/system/misc>admin_ip get
admin_ip: 192.168.100.1
---ATECMDRESULT--- OK
#ONT/system/misc>admin_ip set 192.168.1.1
#ONT/system/misc>admin_mask get
admin_mask: 255.255.255.0
---ATECMDRESULT--- OK
#ONT/system/misc>admin_mask set 255.255.255.0

Notes for Openreach ONT

Serial speed is 9600 8n1. Serial is iactive until the reset button is held down for ~30 seconds, then it’ll break into the ONT> command line. There is no running webserver. Telnet and Dropbear are running (if you disable the firewall) but no login is configured, so not useful.

Miscellaneous Links

MIB file parser for NOKIA’s GPON ONTs (helps you parsing the .mib file located in /mnt/rwdir)
ispreview.co.uk